Skip to Content

POCKETWIZARD PWN10ACC NIKON CABLE

Web Code: 131DAY111  •  Mfr Code: PWN10ACC
POCKETWIZARD PWN10ACC NIKON CABLE
131DAY111-1.jpg
Only $49.99 CAD
 
Low stock online.
In Stock - Usually ships in 24-48 hours but stock is low. Might take 3-4 days to ship out. Additional shipping charges may apply.
{{MyStoreData.Status}} at Henry's {{MyStoreData.StoreName}}
{{MyStoreData.Address}}
Check Other Stores
Call store to confirm:
 
Product Highlights
  • Pre-Trigger Remote Cable
  • For connecting a PlusX, Plus III, FlexTT5 or MultiMAX with ACC port to a Nikon 10-pin remote shutter release terminal
  • Cable lengths: 3' (91.5 cm) and 1' (30 cm)
Read More
 
You must complete all required fields.
 
  • Pre-Trigger Remote Cable
  • For connecting a PlusX, Plus III, FlexTT5 or MultiMAX with ACC port to a Nikon 10-pin remote shutter release terminal
  • Cable lengths: 3' (91.5 cm) and 1' (30 cm)
  • From: 1/8" (3.5 mm) stereo miniphone
  • To: Nikon 10-pin remote shutter release terminal
  • PocketWizard Compatibility:
  • PlusX
  • Plus III
  • FlexTT5
  • MultiMAX with ACC port to a Nikon 10-pin remote shutter release terminal
  • For the Plus II, older MultiMAX or other PocketWizard radios, Please use a N90M3 or a N90M3-P cable
  • This is a special remote shutter release cable called a Pre-Trigger Cable
  • A Pre-Trigger cable controls both the half-press and full-press function of your remote camera's shutter release
  • When a camera is "pre-triggered", it is like holding your camera's shutter release button in the half-pressed or metering/focusing position
  • This cable contains a "no diode" circuit necessary only for the newer Nikon cameras, but will work with other cameras as listed below
  • It will not work with the Nikon D200 or D100 w/ MB-D100. Use the N10-ACC-D220 formally the N90M-ACC cable for those cameras
  • This N10-ACC (formally the N90M-ACC-ND) cable allows a compatible PocketWizard radio to independently control both half-press and full-press functions
  • Compatible with the following radios:
  • PlusX: Use this cable with the PlusX to trigger the camera
  • Plus III: Use this cable with the Plus III?s exclusive 2-stage trigger to wake-up or focus your remote camera just like using the camera's shutter release button
  • FlexTT5: This cable is required for auto-relay mode with E-TTL, or other remote triggering with the FlexTT5
  • You can use a N90M3?P (-P) Pre-Trigger cable or N90M3 standard cable with a FlexTT5, but your remote camera will not be able to relay an E-TTL signal to Speedlites
  • The FlexTT5 does not support the 2-stage trigger function
  • MultiMAX with ?ACC port: Enable a remote zone with your hand-held MultiMAX, and your remote MultiMAX will wake up its remote camera with this cable
  • As long as the zone is turned on, the remote camera will stay awake and respond more quickly and consistently, but also consume the camera's batteries much more quickly
  • When the remote zone is disabled, the camera will enter its normal sleep modes
  • The MultiMAX does not support the 2-stage trigger function
  • NOTE: An older mono motor drive cable and/or pre-release cable can be used instead of an -ACC cable with a FlexTT5 but you will not have E-TTL capability
  • Compatible with cameras using Nikon's 10-pin remote terminal including:
  • Nikon: N90, N90S, F5, F6, F100, D1, D1H, D1X, D2H, D2Hs, D2X, D3, D3S, D3X, D4, D300, D300s, D700, D800, D800E
  • Kodak: DCS Pro SLR/n, DCS Pro 14n, DCS 760, DCS 720x, DCS 660, DCS 660M, DCS 620, DCS 620x
  • Fuji: S3 Pro, S3 Pro UV IS, S5 Pro, IS Pro
 
 

Average Customer Rating

0.0/5 based on 0 Review(s)
  • ({{rbd.NumberOfRatings}})
 
loading
Back top top Skip to Navigation