Skip to Content

POCKETWIZARD CANON N3 MULTIMAX ACCESSORY FLEX

Web Code: 131DAY107
POCKETWIZARD CANON N3 MULTIMAX ACCESSORY FLEX
Only $49.99 CAD
 
Low stock online.
In Stock - Usually ships in 24-48 hours but stock is low. Might take 3-4 days to ship out. Additional shipping charges may apply.
{{MyStoreData.Status}} at Henry's {{MyStoreData.StoreName}}
{{MyStoreData.Address}}
Check Other Stores
Call store to confirm:
 
Product Highlights
  • Pre-Trigger Remote Cable
  • Cable length: 3' / 91.5 cm
  • From: 1/8" / 3.5 mm Stereo Miniphone
Read More
 
 
  • Pre-Trigger Remote Cable
  • Cable length: 3' / 91.5 cm
  • From: 1/8" / 3.5 mm Stereo Miniphone
  • To: Canon N3 Remote Terminal
  • For remotely triggering Canon cameras equipped with an N3 Remote shutter release terminal and controlling half-press function using certain PocketWizard radios
  • PocketWizard Compatibility:
  • PlusX (trigger only)
  • Plus III
  • FlexTT5
  • MultiMAX with ACC port
  • Use the CM-N3-P or CM-N3 for the Plus II, older MultiMAX, or other PocketWizard radios
  • This is a special remote shutter release cable called a Pre-Trigger Cable. A Pre-Trigger cable controls both the half-press and full-press function of your remote camera's shutter release. When a camera is "pre-triggered", it is like holding your camera's shutter release button in the half-pressed or metering/focusing position
  • This -ACC cable allows a compatible PocketWizard radio to independently control both half-press and full-press functions
  • A standard cable works with most PocketWizard radios but has no half-press control, and is for basic remote triggering only
  • A Pre-Release (-P) cable works with most PocketWizard radios. This pre-trigger cable has a switch that allows you to toggle half-press on or off at the camera position, but not remotely
  • Compatible with the following radios:
  • PlusX: Use this cable with the PlusX to trigger the camera
  • Plus III: Use this cable with the Plus III's exclusive 2-stage trigger to wake-up or focus your remote camera just like using the camera's shutter release button
  • FlexTT5: This cable is required for relay mode with E-TTL, or other remote triggering with the FlexTT5. Learn more here. You can use a -P cable or standard cable with a
  • FlexTT5, but your remote camera will not be able to relay an E-TTL signal to Speedlites. The FlexTT5 does not support the 2-stage trigger function
  • MultiMAX with -ACC port: Enable a remote zone with your hand-held MultiMAX, and your remote MultiMAX will wake up its remote camera with this cable. As long as the zone is
  • turned on, the remote camera will stay awake and respond more quickly and consistently, but also consume the camera's batteries much more quickly. When the remote zone is disabled, the camera will enter its normal sleep modes. The MultiMAX does not support the 2-stage trigger function
  • Compatible with cameras using Canon's N3 remote terminal including:
  • Canon
  • EOS-1D Mark II
  • EOS-1D Mark IIN
  • EOS-1D Mark III
  • EOS-1D Mark IV
  • EOS-1Ds
  • EOS-1Ds Mark II
  • EOS-1Ds Mark III
  • EOS-1D X
  • EOS-1V
  • EOS-1V HS
  • EOS-3
  • EOS 5D
  • EOS 5D Mark II
  • EOS 5D Mark III
  • EOS 6D
  • EOS 7D
  • EOS 20D
  • EOS 30D
  • EOS 40D
  • EOS 50D
  • EOS D30
  • EOS D60
  • EOS D2000
  • Kodak
  • DCS 560
  • DCS 520
 
loading
Back top top Skip to Navigation